Hyper-V群集的默认网络

d
徽章 +2
我正在尝试找出Hyper-V群集的默认网络设置的外观。例如，如果我们要采用3x3060，我认为将10GB端口组合在一起，然后添加到类似的外部开关中？那1GBS端口呢？如果有人有几个屏幕截图可以帮助我的好奇心...

干杯

戴夫
\n
\nCheers
\n
\nDave","quoteUsername":"davidhood","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
该主题已关闭以供评论

4个答复

F3RM1N
秩
UserLevel 2
徽章 +10
大卫，
我目前没有屏幕截图，但是您对10Gige的假设正确，并且在设置完成后通常会断开1GIGE适配器：

PS C：userf3rm1n> get-netlbfoteam
名称：NetAdapterTeamMembers：{以太网2，以太网3} teamnics：NetAdapterTeamTeamingMode：switchIndiendentendententLoadBalancingAlgorithm：Dynamicic

ps c：userf3rm1n> get-netlbfoteammember

姓名：以太网2 InterfaceedEscription：Intel（R）82599 10千兆位双端口网络连接Teamnection：NetAdapterteamAdministrativeMode：ActiveOperationalStatus：ActiveTransMitlinkSpspeed（GBPS）：10ReceivelInkSpeed（GBPS）

姓名：以太网3 InterfaceedEscription：Intel（R）82599 10 Gigabit双端口网络连接＃2team：NetAdapterTeamAdministrativeMode：ActiveOperationalStatus：activeTrantionStatus：activeTransMitlinkSpeed（GBPS）
\nI do not have screenshots at this time, but you're correct on your assumptions about the 10GigE, and the 1GigE adapters are usually disconnected after the setup has been completed:
\n
\nPS C:Usersf3rm1n> Get-NetLbfoTeam
\nName : NetAdapterTeamMembers : {Ethernet 2, Ethernet 3}TeamNics : NetAdapterTeamTeamingMode : SwitchIndependentLoadBalancingAlgorithm : Dynamic
\n
\nPS C:Usersf3rm1n> Get-NetLbfoTeamMember
\n
\nName : Ethernet 2InterfaceDescription : Intel(R) 82599 10 Gigabit Dual Port Network ConnectionTeam : NetAdapterTeamAdministrativeMode : ActiveOperationalStatus : ActiveTransmitLinkSpeed(Gbps) : 10ReceiveLinkSpeed(Gbps) : 10FailureReason : NoFailure
\n
\nName : Ethernet 3InterfaceDescription : Intel(R) 82599 10 Gigabit Dual Port Network Connection #2Team : NetAdapterTeamAdministrativeMode : ActiveOperationalStatus : ActiveTransmitLinkSpeed(Gbps) : 10ReceiveLinkSpeed(Gbps) : 10FailureReason : NoFailure","quoteUsername":"f3rm1n","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
d
徽章 +2
谢谢回复。我只是真的在想描绘它如何挂在脑海中。

我们通常会有一个用于管理的VLAN，还有一个用于虚拟服务器等的VLAN。因此，我想我会使用类似于此http://charbelnemnom.com/2014/05/create-a-a--融合 - 网络范围内VMM-2012-r2/。我们是否也将簇热蛋白分开？

CVM是否也可以使用自己的VLAN，因为我还需要将存储流量分开在VLAN上吗？
\n
\nwe would normally have a VLAN for management, and also a VLAN for the virtual servers etc. So I assume I would use the \"converged networking\" design similar to this http:\/\/charbelnemnom.com\/2014\/05\/create-a-converged-network-fabric-in-vmm-2012-r2\/ . Do we separate out the cluster heatbeats too?
\n
\nDoes the CVM go on its own VLAN too, as in do i need to separate the storage traffic over a VLAN as well?","quoteUsername":"davidhood","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
F3RM1N
秩
UserLevel 2
徽章 +10
谢谢，我现在明白了你的意思。我个人只看到一个部署使用了多个逻辑网络，但是如果正确计划，它应该可以正常工作。
关于CVM流量（I/O），除非本地CVM有问题，否则会跨越内部开关
\nRegarding the CVM traffic (I\/O) goes over the Internal switch unless the local CVM has a problem, in that case traffic is re-routed over to another CVM, so host Management and CVM eth0 would fall under the same VLAN","quoteUsername":"f3rm1n","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
Ozzy01
徽章 +5
CVMS ADN主机通常总是在相同的VLAN上推荐用于通信。成像后，您使用VMNETWORKADAPTERVLAN命令为他们设置适当的VLAN，然后设置可以设置LACP Team Bond并删除和禁用1GB，如果不从Hyper-V的角度使用。脚本将为您完成1GB的部分，但是如果添加到现有群集中，则可以更轻松地使用PowerShell命令手动执行。
Ozzy
条款和条件
Learn more about our cookies.<\/a>","cookiepolicy.button":"Accept cookies","cookiepolicy.button.deny":"Deny all","cookiepolicy.link":"Cookie settings","cookiepolicy.modal.title":"Cookie settings","cookiepolicy.modal.content":"We use 3 different kinds of cookies. You can choose which cookies you want to accept. We need basic cookies to make this site work, therefore these are the minimum you can select. Learn more about our cookies.<\/a>","cookiepolicy.modal.level1":"Basic
Functional","cookiepolicy.modal.level2":"Normal
Functional + analytics","cookiepolicy.modal.level3":"Complete
Functional + analytics + social media + embedded videos"}}}">
Baidu