hyper-v集群的默认网络

  • 2015年4月24日
  • 4回复
  • 1027的浏览量
D
徽章 ＋２
我试图找出hyper-v集群的默认网络设置是什么样子的。如果我们以一个3x3060为例，我假设将10GB端口组成一个团队，然后都添加到一个类似的外部交换机?那1gb端口呢?如果有人有一些截图可以帮助我的好奇心……

干杯

戴夫
\n
\nCheers
\n
\nDave","quoteUsername":"davidhood","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

4回复

f3rm1n
排名
Userlevel 2
徽章 + 10
大卫,
我现在没有截图，但你对10GigE的假设是正确的，而且1GigE适配器通常在安装完成后断开:

p C: Usersf3rm1n > Get-NetLbfoTeam
名称:NetAdapterTeamMembers: {Ethernet 2, Ethernet 3}TeamNics: NetAdapterTeamTeamingMode: SwitchIndependentLoadBalancingAlgorithm: Dynamic

p C: Usersf3rm1n > Get-NetLbfoTeamMember

名称:Ethernet 2InterfaceDescription: Intel(R) 82599 10gigabit Dual Port Network ConnectionTeam: NetAdapterTeamAdministrativeMode: ActiveOperationalStatus: ActiveTransmitLinkSpeed(Gbps): 10ReceiveLinkSpeed(Gbps): 10FailureReason: NoFailure

名称:以太网3接口描述:英特尔(R) 82599 10千兆双端口网络连接#2团队:NetAdapterTeamAdministrativeMode: ActiveOperationalStatus: ActiveTransmitLinkSpeed(Gbps): 10ReceiveLinkSpeed(Gbps): 10FailureReason: NoFailure
\nI do not have screenshots at this time, but you're correct on your assumptions about the 10GigE, and the 1GigE adapters are usually disconnected after the setup has been completed:
\n
\nPS C:Usersf3rm1n> Get-NetLbfoTeam
\nName : NetAdapterTeamMembers : {Ethernet 2, Ethernet 3}TeamNics : NetAdapterTeamTeamingMode : SwitchIndependentLoadBalancingAlgorithm : Dynamic
\n
\nPS C:Usersf3rm1n> Get-NetLbfoTeamMember
\n
\nName : Ethernet 2InterfaceDescription : Intel(R) 82599 10 Gigabit Dual Port Network ConnectionTeam : NetAdapterTeamAdministrativeMode : ActiveOperationalStatus : ActiveTransmitLinkSpeed(Gbps) : 10ReceiveLinkSpeed(Gbps) : 10FailureReason : NoFailure
\n
\nName : Ethernet 3InterfaceDescription : Intel(R) 82599 10 Gigabit Dual Port Network Connection #2Team : NetAdapterTeamAdministrativeMode : ActiveOperationalStatus : ActiveTransmitLinkSpeed(Gbps) : 10ReceiveLinkSpeed(Gbps) : 10FailureReason : NoFailure","quoteUsername":"f3rm1n","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
D
徽章 ＋２
谢谢你的回复。我只是试着在脑海中勾勒出它们是如何联系在一起的。

我们通常会有一个VLAN用于管理，也有一个VLAN用于虚拟服务器等。所以我假设我将使用类似于http://charbelnemnom.com/2014/05/create-a-converged-network-fabric-in-vmm-2012-r2/的“融合网络”设计。我们也要把集束热跳动分开吗?

CVM是否也在自己的VLAN上运行，就像我需要在一个VLAN上分离存储流量一样?
\n
\nwe would normally have a VLAN for management, and also a VLAN for the virtual servers etc. So I assume I would use the \"converged networking\" design similar to this http:\/\/charbelnemnom.com\/2014\/05\/create-a-converged-network-fabric-in-vmm-2012-r2\/ . Do we separate out the cluster heatbeats too?
\n
\nDoes the CVM go on its own VLAN too, as in do i need to separate the storage traffic over a VLAN as well?","quoteUsername":"davidhood","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
f3rm1n
排名
Userlevel 2
徽章 + 10
谢谢，我现在明白你的意思了;我个人只看到过一个部署使用了两个以上的逻辑网络，但如果计划正确，它应该可以正常工作。
关于CVM流量(I/O)通过内部交换机，除非本地CVM有问题，在这种情况下，流量被重新路由到另一个CVM，所以主机管理和CVM eth0将落在同一个VLAN
\nRegarding the CVM traffic (I\/O) goes over the Internal switch unless the local CVM has a problem, in that case traffic is re-routed over to another CVM, so host Management and CVM eth0 would fall under the same VLAN","quoteUsername":"f3rm1n","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
ozzy01
徽章 ＋5
为了便于通信，通常建议cvm和主机在同一个VLAN上。一旦成像，您可以使用VMNetworkAdapterVlan命令为它们设置您需要的适当的VLAN，然后set可以设置LACP团队绑定，并删除和禁用您的1Gbs，等等，如果不是从Hyper-V的角度使用。脚本将为您完成1Gb的部分，但如果添加到现有的集群，使用powershell命令手动完成更容易。
奥兹

回复


Baidu