我有一些系统可以从Baremetal重建。它们都是安全启动的安全启动，要禁用此设备，我必须在现场更换跳线。
基金会似乎不起作用，我假设凤凰靴只是启用了UEFI，因此刚刚被跳过。我可以用来裸机构建这些系统的版本或过程。如果需要，我可以轻松地手动安装ESXI。
只是试图避免进入共同区域以避免跳投的方式。
最好的答案nupur.Sakhalkar
Considering these Nutanix nodes are not a part of any cluster, follow the below process for\u00a0manual imaging of these bare metal nodes:<\/p>
1) Create AOS+Hypervisor+Phoenix ISO from any existing CVM available in any other cluster (which is on same AOS version needed on these bare metal nodes) or via foundation VM using the steps mentioned in KB-3523<\/a><\/p> 2) Once the\u00a0AOS+Hypervisor+Phoenix ISO is created, download it to your local machine via WinSCP<\/p> 3) Login to IPMI console of each of these bare-metal nodes<\/p> 4)\u00a0Select Console Redirection<\/strong> from the Remote Console<\/strong> drop-down list of the main menu, and then click the Launch Console<\/strong> button.<\/p> 5) Open this console and then\u00a0Select Virtual Storage<\/strong> from the Virtual Media<\/strong> drop-down list on\u00a0this\u00a0remote IPMI JAVA console main menu.<\/p> 6)\u00a0Click the CDROM&ISO<\/strong> tab in the Virtual Storage<\/strong> window, select ISO File<\/strong> from the Logical 7)\u00a0In the browse window, go to where the ISO image (AOS+Hypervisor+Phoenix ISO) is located, select the image, and then click the Open button.<\/p> 8)\u00a0Click the Plug In<\/strong> button and then the OK<\/strong> button to close the Virtual Storage window.<\/p> 9)\u00a0In the remote console main menu, select Set Power Reset<\/strong> in the Power Control<\/strong> drop-down 10) Once the node boots into phoenix, confirm the Block serial, node serial, node position, AOS and hypervisor details. Also, for installing hypervisor and AOS on the bare metal NX node - select\u00a0Install CVM (Wipes Existing Data!)and Install, Configure Hypervisor<\/strong> action in the phoenix window.\u00a0\u00a0When all the fields are correct, click the Start<\/strong> button.\u00a0Installation begins and takes ~30 minutes.<\/p> 11)\u00a0After installation completes, unmount the ISO. For NX nodes,\u00a0In the Virtual Storage<\/strong> window, click CDROM&ISO > Plug Out<\/strong>.<\/p> 12) Once the ISO is plugged out, at the reboot prompt in the IPMI JAVA remote console, type Y<\/strong> to restart the node.<\/p> 13)\u00a0On ESXi and AHV, the node restarts with the new image, additional configuration tasks run, and then the host restarts again. Wait until this stage completes (typically ~30 minutes 14) Once both the hypervisor and AOS installation is completed, proceed with doing the network configuration (hypervisor + CVM) on these nodes by assigning appropriate IP address and other network configuration on it.\u00a0<\/p> 15) You will need to follow the above process for all nodes that you plan to re-image. Considering that these nodes are not a part of the cluster, you can perform the above steps on all nodes in parallel.<\/p> At this point, the manual\u00a0imaging process for bare-metal nodes will be completed. However, there won\u2019t be any cluster created for it. If your end goal is to create a cluster out of these newly imaged nodes, then perform the steps mentioned in the Manual Cluster Creation<\/a> guide to create a Nutanix cluster from these nodes.\u00a0<\/p>","className":"post__content__best_answer"}">
Drive Type field drop-down list, and click the Open Image<\/strong> button.<\/p>
list. This causes the system to reboot to the selected image.<\/p>
depending on the hypervisor) before accessing the node.\u00a0<\/p>
