解决了

IPMItool全双工命令

  • 2014年10月4日
  • 4回复
  • 1567的浏览量
R
Userlevel 1
徽章 + 8
你好,

有人知道是否有一个IPMItool命令设置接口为100MB全双工吗?这个选项是否可以更改它?

我们有一些IPMI问题，连通性经常下降。我们正在与网络合作，检查他们的方面，我们已经做了各种各样的事情来测试/隔离问题。在网络交换机侧，端口已从1GgE配置为100MB。

来自网络的一个建议是将IPMI接口设置为100MB的全双工。

谢谢你！
房车
图标

最佳答案dlink72014年10月6日20:00

查看原始
    \n
    \nDoes anyone know if there is an IPMItool command to set the interface to 100MB full duplex? Is this option to change it even available?
    \n
    \nWe are having some IPMI issue where connectivity drops every so often. We are working with networking to check their side, and we've done various things to test\/isolate the issue. On the network switch side, the ports have been configured to 100MB from 1GgE.
    \n
    \nOne suggestion that came up from networking is to set the IPMI interface to 100MB full duplex.
    \n
    \nThank you.
    \nRV","quoteUsername":"rvillarin","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

    4回复

    T
    Userlevel 2
    徽章 + 14
    你是否验证了你的物理电缆的完整性?除非交换机端口配置错误或没有配置为自动协商，否则唯一会打乱100MB全双工自动协商的常见事情是沿着电缆的物理故障。除此之外，如果你真的如果你想强制全双工，你可以通过谷歌搜索Super Micro IPMI命令行引用来找到一些命令文档，因为这就是你的OEM IPMI实际上是什么。粗略地搜索一下，我找到了这个超级微KB，但它可能与你的IPMI固件版本有关，也可能无关:http://www.supermicro.com/support/faqs/faq.cfm?faq=15867
    really<\/i> want to force Full Duplex you might be able to find some command documenatation by googling for Super Micro IPMI Command Line references as that is what your OEM IPMI actually is. Rough googling got me to this Super Micro KB, but it may or may not be relevant depending on your IPMI firmware revision: http:\/\/www.supermicro.com\/support\/faqs\/faq.cfm?faq=15867","quoteUsername":"tjagoda","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
    dlink7
    Userlevel 4
    徽章 + 19
    IPMI仅为100mb /s。不过你也可以使用1gb /s的备用网卡。

    您可以尝试通过命令行运行此操作

    /ipmitool LAN print
    \n
    \nYou can try running this via the command line
    \n
    \n\/ipmitool lan print 1","quoteUsername":"dlink7","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
    dlink7
    Userlevel 4
    徽章 + 19
    顺便说一下，IPMI推荐使用auto
    R
    Userlevel 1
    徽章 + 8
    你好,

    谢谢你所有的回复。感谢。

    结果是，这些端口被硬编码为100。把他们换成自动谈判解决了这个问题。

    你是对的!!谢谢。

    房车
    \n
    \nThank you for all the replies. Much appreciated.
    \n
    \nIt turned out that the ports were hard coded to run at 100. Switching them to auto negotiate resolved the problem.
    \n
    \nDLINK7 - you were right on the money!!! Thanks.
    \n
    \nRV","quoteUsername":"rvillarin","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

    回复


    Baidu