解决了

ipmitool完整双工命令

r
Userlevel 1
徽章 +8
你好 -

有谁知道是否有IPMITOL命令将接口设置为100MB完整双工？是否可以更改此选项？

我们遇到了一些IPMI问题，其中连通性经常下降。我们正在与网络合作检查他们的一方，并且我们已经做了各种事情来测试/隔离问题。在网络开关侧，端口已从1GGE配置为100MB。

网络提出的一个建议是将IPMI接口设置为100MB完整双工。

谢谢。
RV
图标

最好的答案dlink72014年10月6日，20:00

查看原件
    \n
    \nDoes anyone know if there is an IPMItool command to set the interface to 100MB full duplex? Is this option to change it even available?
    \n
    \nWe are having some IPMI issue where connectivity drops every so often. We are working with networking to check their side, and we've done various things to test\/isolate the issue. On the network switch side, the ports have been configured to 100MB from 1GgE.
    \n
    \nOne suggestion that came up from networking is to set the IPMI interface to 100MB full duplex.
    \n
    \nThank you.
    \nRV","quoteUsername":"rvillarin","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

    4个答复

    t
    UserLevel 2
    徽章 +14
    您是否验证了物理电缆的完整性？除非开关端口被错误配置或不配置为自动调节，否则唯一会遇到100MB Full Duplex的自动连接的常见事物是沿线沿线的物理故障。除此之外，如果你真的想要强制完整的双工，您可能可以通过搜索搜索超级Micro IPMI命令行引用来找到一些命令文档，因为这就是您的OEM IPMI实际上。粗略的谷歌搜索使我进入了这个超级微型KB，但根据您的IPMI固件修订：http：//www.supermicro.com/support/faqs/faqs/faq.cfm?faq = 15867
    really<\/i> want to force Full Duplex you might be able to find some command documenatation by googling for Super Micro IPMI Command Line references as that is what your OEM IPMI actually is. Rough googling got me to this Super Micro KB, but it may or may not be relevant depending on your IPMI firmware revision: http:\/\/www.supermicro.com\/support\/faqs\/faq.cfm?faq=15867","quoteUsername":"tjagoda","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
    dlink7
    UserLevel 4
    徽章 +19
    IPMI仅为100 MB/s。虽然您可以使用1 GB/s的Standby NIC。

    您可以尝试通过命令行运行此操作

    /ipmitool lan打印1
    \n
    \nYou can try running this via the command line
    \n
    \n\/ipmitool lan print 1","quoteUsername":"dlink7","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
    dlink7
    UserLevel 4
    徽章 +19
    BTW Auto是IPMI的推荐
    r
    Userlevel 1
    徽章 +8
    大家好 -

    谢谢您的所有答复。非常感激。

    事实证明，端口很难编码以100处运行。切换它们以自动谈判解决了问题。

    dlink7-你是正确的！！！谢谢。

    RV
    \n
    \nThank you for all the replies. Much appreciated.
    \n
    \nIt turned out that the ports were hard coded to run at 100. Switching them to auto negotiate resolved the problem.
    \n
    \nDLINK7 - you were right on the money!!! Thanks.
    \n
    \nRV","quoteUsername":"rvillarin","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

    回复


    Baidu