解决了

Windows 2008 R2从ESXI迁移到AHV

j
徽章

我刚刚从ESXI 6.0到AHV迁移了Windows 2008 R2的VM，但是当我在Nutanix群集中打开它时，我得到了蓝屏。我使用了3.4.1版的Move版本，有人知道发生了什么。

图标

最好的答案杰里米2020年2月26日，19:20

@Jose_orozco<\/user-mention>\u00a0<\/p>

I understand you migrated the VM using Move 3.4.1. If you are using fully automated migration, Move should not start the migration before confirming VirtIO\u00a0drivers are installed. This includes VirtIO drivers for disk, memory, and network. If you changed to manual mode you would need to ensure you installed the drivers yourself.<\/p>

Since you did not indicate there was any error reported from Move, I expect the Move server reported the migration was successful. Please clarify if I\u2019m wrong.<\/p>

If you wanted to isolate whether this could be a disk driver issue, the steps to convert the virtual disk to IDE are in the KB \u201cAHV | How to install VirtIO drivers for Microsoft Windows Server 2008<\/a>\u201d<\/p>

I\u2019m guessing it may be something else, though I\u2019m not sure what it would be since 2008 R2 is fully supported on AHV. ref: Compatibility Matrix<\/a><\/p>

If we had some more detail on what is seen from the BSOD, possibly we could come to a more definite\u00a0answer. Share a screenshot here if you like, but I\u2019d expect quicker resolution if you raise a case.

Thanks,<\/p>

Jeremy<\/p>","className":"post__content__best_answer"}">

查看原件
I just migrated a VM with Windows 2008 R2 from ESXi 6.0 to AHV but I got blue screen when I turned it on in nutanix cluster. I used move version 3.4.1 somebody knows what happened.<\/p>","quoteUsername":"Jose_orozco","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
该主题已关闭以供评论

6个答复

朱布兰
秩
UserLevel 3
徽章 +3

你好 @Jose_orozco

您将必须在AHV上安装Windows VMS的Virtio，您可以从中下载最新版本这里。下载后，通过Prism将其上传到您的群集。

当Virtio映像在您的群集中时，转到VM列表>双击Prism中的Windows VM，添加带有此配置的磁盘：

  • type =光盘
  • 操作=来自图像服务的克隆
  • 总线类型=IDE
  • 图像=附加您先前下载的Virtio图像。
  • 点击添加

查看此页面以获取更多信息和说明：https://portal.nutanix.com/#/page/docs/details?targetid=amf-guide-aos-v50:vmm-vm-vm-vm-virtio-ahv-c.html

Hi @Jose_orozco<\/user-mention>\u00a0<\/p>

You will have to install VirtIO for windows VMs on AHV, you can download the latest version from here<\/a>. after downloading it, upload it to your cluster via Prism.<\/p>

When the VirtIO image is in your cluster, go to the VM list > double click on the windows VM in Prism, add a disk with this configuration:\u00a0<\/p>

阿卢西亚尼
UserLevel 7
徽章 +34

你好 @Jose_orozco让社区知道上面的答复是否有帮助。谢谢：竖起大拇指：

在Twitter上关注我：https：//twitter.com/angeloluciani
Hi @Jose_orozco<\/user-mention> let the community know if the reply above helped. Thanks \":thumbsup:\"<\/p>","quoteUsername":"aluciani","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">
b
UserLevel 2
徽章 +12

希望您有时间安装Virtio驱动程序（在获得BSOD之前）。

另一个选项是在源服务器上安装Virtio驱动程序，因此Windows Plug＆Play将安装SCSI控制器驱动程序，并且在使用正确的驱动程序迁移后，该服务器将自动启动。

问候，

巴特

hopefully, you have the time to install the virtio drivers (before getting the BSOD).<\/p>

Another option is to install the virtio drivers on the source server, so Windows Plug&Play will install the SCSI controller driver and the server will boot automatically after migration with the correct drivers.<\/p>

\u00a0<\/p>

regards,<\/p>

Bart<\/p>","quoteUsername":"badonders","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

j
徽章

你好 @aluciani我已经尝试了Jubran的选项，但我也没有工作，我也想说我在迁移之前安装了美德，但不起作用，因为当蓝色屏幕蓝色到达时，Windoes不会运行

我仍然专注于你的评论

谢谢

Hi @aluciani<\/user-mention>\u00a0\u00a0I have been tried with jubran\u2019s option but did not work also I want to say I Installed the the VirtIO before the migration but does not work because the windoes doesn't run when the blue screen blue \u00a0got to apear<\/p>

i remain attentive to your comments\u00a0<\/span><\/p>

\u00a0<\/p>

thanks<\/p>

\u00a0<\/p>","quoteUsername":"Jose_orozco","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

b
UserLevel 2
徽章 +12

你好 @Jose_orozco，，，，

选项是克隆磁盘到IDE总线。服务器将启动（非常缓慢）。然后，您可以检查SCSI控制器的驱动程序，并最终重新安装该驱动程序。当驱动程序安装成功时，您可以再次克隆磁盘，但现在可以转到SCSI控制器。

此后，服务器应在没有任何问题的情况下运行（至少如果SCSI控制器是问题。）

您称Nutanix的支持吗？毕竟，Windows 2008R2受到最新的Virtio驱动程序的支持。他们很乐意为您提供支持。

问候，

巴特

Hi @Jose_orozco<\/user-mention>,<\/p>

Option is to clone disk(s) to ide bus. \u00a0Server will start (very slowly). Then you can check the drivers of the SCSI controller, and eventually reinstall this driver. When driver installation is successful, you can clone the disks again, but now to a SCSI controller.<\/p>

Server should be running without any problem after that (at least, if the SCSI Controller is the problem.)<\/p>

Did you call Nutanix Support? After all, Windows 2008R2 is supported with the latest VirtIO drivers. They would be happy to support you.<\/p>

\u00a0<\/p>

Regards,<\/p>

Bart<\/p>","quoteUsername":"badonders","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

杰里米
秩
UserLevel 3
徽章 +4

@Jose_orozco

我了解您使用MOVE 3.4.1迁移VM。如果您使用的是全自动迁移，则在确认Virtio驱动程序之前，移动不应启动迁移。这包括用于磁盘，内存和网络的Virtio驱动程序。如果您更改为手动模式，则需要确保自己安装驱动程序。

由于您没有表明Move报告了任何错误，因此我预计Move Server报告说迁移成功。请澄清一下我错了。

如果您想隔离这是否可能是磁盘驱动程序问题，则将虚拟磁盘转换为IDE的步骤位于KB中”ahv |如何为Microsoft Windows Server安装Virtio驱动程序2008透明

我猜这可能是其他的，尽管我不确定自2008 R2以来AHV的支持以来会有什么。参考：兼容矩阵

如果我们从BSOD中看到了更多的细节，那么我们可能会得到更明确的答案。如果您愿意，请在此处共享屏幕截图，但是如果您提出案例，我希望更快的分辨率。

谢谢，

杰里米

@Jose_orozco<\/user-mention>\u00a0<\/p>

I understand you migrated the VM using Move 3.4.1. If you are using fully automated migration, Move should not start the migration before confirming VirtIO\u00a0drivers are installed. This includes VirtIO drivers for disk, memory, and network. If you changed to manual mode you would need to ensure you installed the drivers yourself.<\/p>

Since you did not indicate there was any error reported from Move, I expect the Move server reported the migration was successful. Please clarify if I\u2019m wrong.<\/p>

If you wanted to isolate whether this could be a disk driver issue, the steps to convert the virtual disk to IDE are in the KB \u201cAHV | How to install VirtIO drivers for Microsoft Windows Server 2008<\/a>\u201d<\/p>

I\u2019m guessing it may be something else, though I\u2019m not sure what it would be since 2008 R2 is fully supported on AHV. ref: Compatibility Matrix<\/a><\/p>

If we had some more detail on what is seen from the BSOD, possibly we could come to a more definite\u00a0answer. Share a screenshot here if you like, but I\u2019d expect quicker resolution if you raise a case.

Thanks,<\/p>

Jeremy<\/p>","quoteUsername":"JeremyJ","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

Learn more about our cookies.<\/a>","cookiepolicy.button":"Accept cookies","cookiepolicy.button.deny":"Deny all","cookiepolicy.link":"Cookie settings","cookiepolicy.modal.title":"Cookie settings","cookiepolicy.modal.content":"We use 3 different kinds of cookies. You can choose which cookies you want to accept. We need basic cookies to make this site work, therefore these are the minimum you can select. Learn more about our cookies.<\/a>","cookiepolicy.modal.level1":"Basic
Functional","cookiepolicy.modal.level2":"Normal
Functional + analytics","cookiepolicy.modal.level3":"Complete
Functional + analytics + social media + embedded videos"}}}">
Baidu