Join this episode for more Stories from the EUC Road as Sean Donahue (Nutanix) and Al Solorzano (E360) tackle this all too familiar question. But does it have to an \u201cOR\u201d statement? Can you have an \u201cAND\u201d statement instead? Tune in to learn more about performance in EUC, happy employees and how you might sleep better at night in the age of Malware and Ransomware.<\/p><\/oembed>

Resources<\/p>

解决了

Horizon View Instant Clone & Nutanix Firmware updates....Sanity check..

  • 24 May 2019
  • 4 replies
  • 1852年的观点

Badge
我们已经在Nutanix上运行了Horizo​​n View环境,待了6个月多一点,我准备进行第一轮磁盘/BIOS等固件更新。我的主要关心是,由于我们正在利用Horizo​​n View Instant Clones,因此每个主机上的“父映像”上有一个功能...我们正在运行View 7.5,并且我在以前的版本中知道,有一个称为“ Instant Clone”的属性维护“您将值更改为1,它将关闭并删除该父映像,从而将任何台式机放在该主机上的配置中,从而使您可以将其放置在维护模式下并进行业务。我需要一些清晰度(和理智检查!),如何允许(或者我不使用LCM)执行这些必要的固件更新而不将我的视图环境放下...使用了24x7的环境并且无法承受中断..请给我看你的轮子,所以我无需重新发明!谢谢社区!
icon

Best answer byVirtuallySteve30 September 2019, 18:48

\n
    \n
  1. Edit the value for \"InstantClone.Maintenance\" to 1 \n
  2. After a few minutes, vCenter and Horizon View will see that value, and shut down\/delete the cp-parent VMs on that host, and the value will change to 3 \n
  3. Once you see the cp-parent VMs are gone, you can go into Prism and go to LCM, once you have performed an inventory, you should be able to put a check next to the host you want to upgrade (ONLY CHECK THE HOST YOU WISH TO UPGRADE!). \n<\/ol>LCM will take care of the rest. It will invoke DRS (make sure HA Admission control is disabled or Nutanix will fail the process). It will migrate all workloads off the host, shut down the CVM, place the host into maintenance mode and begin the firmware upgrades. WHen the host comes back online, all your health checks are good, just change the value back to 0, and move some workloads back. When new VMs are needed in your instant clone pool, the cp-parent images will be spawned again. I would generally wait until the cp-parent images were re-spawned before moving to the second host. I only have 4 nodes in my instant clone cluster currently, so depending on how many firmware are needed bank on at least an hour per node I am on AOS 5.10.5 LTS, as there were some much needed improvements in LCM in the 5.10.x line up, so be sure you are on that build or higher.
    \n
    \nNOTE: if you have ANY nodes that require SATADOM upgrades, you HAVE to apply them on every node before any other firmware shows as available.
    \n Let me know, i'm happy to answer any other questions!","className":"post__content__best_answer"}">
View original

This topic has been closed for comments

4 replies

Badge
@VirtuallySteve,

您是否找到了这个答案?我们使用即时克隆站立一个新的集群并遇到了同一件事。我想知道我是否只需要一次手动执行每个节点,而不是我更喜欢的滚动升级方法。希望您找到一个更好的解决方案 - 我很想听听。
Badge
MJG,目前,执行运行即时克隆的节点的最佳方法是单独的。VMware使它变得更加容易,因为您会注意到每个节点(在VSPhere Web客户端中)具有自定义属性“ instantclone.saintclone.maintenance”,并且当前值应为0。我的步骤要升级固件或任何您的步骤需要将主机置于维护模式下:


  1. Edit the value for "InstantClone.Maintenance" to 1
  2. After a few minutes, vCenter and Horizon View will see that value, and shut down/delete the cp-parent VMs on that host, and the value will change to 3
  3. Once you see the cp-parent VMs are gone, you can go into Prism and go to LCM, once you have performed an inventory, you should be able to put a check next to the host you want to upgrade (ONLY CHECK THE HOST YOU WISH TO UPGRADE!).
LCM will take care of the rest. It will invoke DRS (make sure HA Admission control is disabled or Nutanix will fail the process). It will migrate all workloads off the host, shut down the CVM, place the host into maintenance mode and begin the firmware upgrades. WHen the host comes back online, all your health checks are good, just change the value back to 0, and move some workloads back. When new VMs are needed in your instant clone pool, the cp-parent images will be spawned again. I would generally wait until the cp-parent images were re-spawned before moving to the second host. I only have 4 nodes in my instant clone cluster currently, so depending on how many firmware are needed bank on at least an hour per node I am on AOS 5.10.5 LTS, as there were some much needed improvements in LCM in the 5.10.x line up, so be sure you are on that build or higher.



注意:如果您有任何需要SATADOM升级的节点,则必须在所有其他固件显示之前将它们应用于每个节点。

让我知道,我很高兴回答其他任何问题!
Badge
@VirtuallySteve

Thanks for the quick reply! I was able to get firmware on a couple of nodes using this method yesterday and it went smoothly.



不要为主题提出太多内容,但是您是否介意我问您如何处理AOS升级?我只使用了滚动升级方法,这似乎会破裂。是否可以一次执行AOS一个节点/让过程等待您切换下一个节点instantclone.maintenance至1?
Badge

mjg, no worries, I am really glad to help!

Glad your firmware updates are going well! Definitely take it slow to ensure everything is healthy between node upgrades. AOS is completely non-disruptive to the hosts. No need to place the hosts in maintenance mode, as it installs AOS on each CVM, and reboots them in a staged/safe fashion. Let the Nutanix cluster do its thing for the CVMs.

我强烈建议您从事的第一批固件/AOS升级工作,请与Nutanix打开主动票。让他们进行预付健康检查,他们将在您的工作期间保持门票打开(如果您有问题,您将获得下一个在已经打开的机票的情况下获得的支持)。我曾经在下一个工作日回电,让他们进行升级后的健康检查。我很乐意分享自己的命令等,我现在自己运行,以确保事情健康。

Learn more about our cookies.<\/a>","cookiepolicy.button":"Accept cookies","cookiepolicy.button.deny":"Deny all","cookiepolicy.link":"Cookie settings","cookiepolicy.modal.title":"Cookie settings","cookiepolicy.modal.content":"We use 3 different kinds of cookies. You can choose which cookies you want to accept. We need basic cookies to make this site work, therefore these are the minimum you can select. Learn more about our cookies.<\/a>","cookiepolicy.modal.level1":"Basic
Functional","cookiepolicy.modal.level2":"Normal
Functional + analytics","cookiepolicy.modal.level3":"Complete
Functional + analytics + social media + embedded videos"}}}">
Baidu