X射线：零配置网络

  • 2021年11月4日
  • 0答复
  • 27意见
r
秩
UserLevel 2
徽章 +4

如果没有DHCP服务器，或者无法创建足够大的X射线VM的示波器时，请使用零配置来进行自分配的IP地址。

零配置网络是主机自我分配IP地址的IP地址的标准。X射线使用IPv4。使用保留地址169.254.0.0/16。

此功能消除了对手动IP地址配置或DHCP的需求。


sRMCVTtRUI5sX5t_6R-suIGa-td40vwiN1P6muuQxmXdN_DI8sFrw_DumtF8rA-edY8zuZRdOrBqKXkNmRit6We7_BCx2Q3QjQYjtQmSnBH7VDTf6Lwuk2ULHLZsrmWWB2nBUAKm

要使用零配置网络，请配置工作负载VM和已部署的X射线VM的第二个NIC以使用相同的Layer-2网络。

对于ESXI，.OVA自动添加第二个NIC。对于AHV，手动添加第二个NIC。当您添加时，第二个NIC会自动拾取零配置设置，因此无需额外的配置。


在ESXI上启用IPMI发现

在ESXI上启用基于Web的企业管理（WBEM）

  • 在ESXI 6.5上，默认情况下，IPMI发现过程被禁用，这导致目标创建过程中的连接不成功。

  • 如果您没有启用WBEM，请启用WBEM，然后重试IPMI发现。否则，请在X射线目标创建期间手动输入IPMI数据。

  • X射线为IPMI发现支持以下ESXI版本。

    • vSphere ESXI 6.7

    • vsphere esxi 6.5

    • vsphere esxi 6.0

    • vSphere ESXI 5.5

    • vSphere ESXI 5.1

    • vSphere ESXI 5.0

  • 如果您安装了第三方CIM提供商VSphere安装捆绑包（VIB），则WBEM服务会自动运行。

程序：

将WBEM作为每个ESXI主机上的根用户连接。

  • 在每个ESXI主机上运行以下命令。

    • ESXCLI系统WBEM SET - 可启用true

  • 要验证WBEM启用成功，请使用以下命令。

    • ESXCLI系统WBEM获取

拉阿吉
When no DHCP server is available, or where creating a scope large enough for X-Ray VMs is not possible, use zero-configuration for self-assigned IP addressing.<\/span><\/p>

\u00a0<\/p>

Zero-configuration networking is a standard for IP addressing where a host self-assigns an IP address. X-Ray uses IPv4. which uses the reserved addresses 169.254.0.0\/16.<\/span><\/p>

\u00a0<\/p>

This feature eliminates the need for manual IP address configuration or DHCP.<\/span><\/p>


\u00a0<\/p>

\"sRMCVTtRUI5sX5t_6R-suIGa-td40vwiN1P6muuQxmXdN_DI8sFrw_DumtF8rA-edY8zuZRdOrBqKXkNmRit6We7_BCx2Q3QjQYjtQmSnBH7VDTf6Lwuk2ULHLZsrmWWB2nBUAKm\"<\/span><\/p>

\u00a0<\/p>

To use zero-configuration networking, configure the workload VMs and the second NIC of the deployed X-Ray VM to use the same layer-2 network.<\/span><\/p>

\u00a0<\/p>

For ESXi, the .ova adds the second NIC automatically. For AHV, add the second NIC manually. The second NIC automatically picks up the zero-configuration settings when you add it, so no extra configuration is necessary.<\/span><\/p>


\u00a0<\/p>

Enabling IPMI Discovery on ESXi<\/strong><\/p>

\u00a0<\/p>

Enable web-based enterprise management (WBEM) for IPMI discovery on ESXi<\/span><\/p>

\u00a0<\/p>

  • \t

    On ESXi 6.5, the IPMI discovery process is disabled by default, which results in unsuccessful connections during target creation.<\/span><\/p>\t<\/li>\t

  • \t

    If you do not have WBEM enabled, enable WBEM and then retry IPMI discovery. Otherwise, enter the IPMI data manually during X-Ray\u00a0 target creation.<\/span><\/p>\t<\/li>\t

  • \t

    X-Ray supports the following ESXi versions for IPMI discovery.<\/span><\/p>\t

    • \t\t

      vSphere ESXi 6.7<\/span><\/p>\t\t<\/li>\t\t

    • \t\t

      vSphere ESXi 6.5<\/span><\/p>\t\t<\/li>\t\t

    • \t\t

      vSphere ESXi 6.0<\/span><\/p>\t\t<\/li>\t\t

    • \t\t

      vSphere ESXi 5.5<\/span><\/p>\t\t<\/li>\t\t

    • \t\t

      vSphere ESXi 5.1<\/span><\/p>\t\t<\/li>\t\t

    • \t\t

      vSphere ESXi 5.0<\/span><\/p>\t\t<\/li>\t<\/ul><\/li>\t

    • \t

      If you have third-party CIM provider vsphere installation bundles (VIB) installed, WBEM services run automatically.<\/span><\/p>\t<\/li><\/ul>

      \u00a0<\/p>

      Procedure:<\/span><\/p>

      \u00a0<\/p>

      Connect WBEM as a root user on each ESXi host.<\/span><\/p>

      \u00a0<\/p>

      • \t

        Run the following command on each ESXi host.<\/span><\/p>\t

        • \t\t

          esxcli system wbem set --enable true<\/span><\/p>\t\t<\/li>\t<\/ul><\/li>\t

        • \t

          To verify that WBEM enabling was successful, use the following command.<\/span><\/p>\t

          • \t\t

            esxcli system wbem get<\/span><\/p>\t\t<\/li>\t<\/ul><\/li><\/ul>","quoteUsername":"raaji","translations":{"Common":{"like":"Like","unlike":"Unlike"},"Forum":{"Quote":"Quote","Share":"Share"}}}">

该主题已关闭以供评论
Baidu